Hinkley-lighting REVERE 1180SN Manuel d'utilisateur télécharger pdf

Drawing 2 - Assembly

start here

1. To install glass, open side door (not shown on drawing 2) of ﬁxture by lifting up on

the small wire tab located on the right side of the ﬁxture when looking at it straight on

- see Drawing 2.

2. Install small panel of glass (1) on left side of ﬁxture by slipping the glass into the

cage through the door opening (2) at a slight angle and around the socket (3) and into

position.

3. Fold glass clips (4) located at the top and bottom of the cage so they contact the

glass and hold it in position.

4. Repeat procedure for front and back large panels of glass. Starting with the back

panel.

5. When all glass panels are installed, the candle sleeve (5) can be slipped over socket

(3).

6. Fixture can now be lamped accordingly.

assembly instructions

1180

Note: Maximum wattage for 1180 ﬁxture is 60 watts per bulb.

1. Find a clear area in which you can work.

2. Unpack ﬁxture and glass from carton.

3. Carefully review instructions prior to assembly.

*** The construction of this ﬁxture will be accomplished by ﬁrst installing the

glass, mounting the mounting strap to the junction box, making all necessary

electrical connections, and then mounting the ﬁxture to the wall.

Family: Revere Item No. 1180 SN

6.1.10

Drawing 1 - Fixture Mounting

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)

AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING

INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED

ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

Make electrical connections from supply wire to ﬁxture lead wires. Refer to instruction

sheet (I.S. 18) and follow all instructions to make all necessary wiring connections.

Then refer back to this sheet to continue installation of this ﬁxture.

1. Prepare mounting strap (A) by threading the two 1 1/4” long mounting screws (B)

into the back of the mounting strap (A) - see Drawing 1.

• Be sure the holes into which the screws are threaded match the spacing of holes (D)

in the backplate (E).

2. Attach mounting strap (A) to junction box (J) using two 1” screws (C).

1. To mount ﬁxture, slip the two mounting screws (B) through the two mounting holes

(D) in the backplate (E) - see Drawing 1.

2. While holding ﬁxture in place, thread the two ball knobs (F) on to the end of the

mounting screws (B), and tighten.

H I N K L E Y L I G H T I N G 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com

1 2 3

Drawing 2 - Assembly 1
Drawing 1 3

Résumé du contenu

Page 1 - Drawing 2 - Assembly

Drawing 2 - Assemblystart here1. To install glass, open side door (not shown on drawing 2) of ﬁxture by lifting up on the small wire tab located on th

Page 2

I.S. 18 wiring grounding instructionsSAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPL

Page 3 - Drawing 1

I.S.200 Caulking Instruction____start here---Drawing

Commentaires sur ces manuels

Pas de commentaire

Hinkley-lighting REVERE 1180SN Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Hinkley-lighting REVERE 1180SN. Hinkley Lighting REVERE 1180SN User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Hinkley-lighting REVERE 1180SN