Hinkley-lighting STRATFORD 1351 Manuel d'utilisateur télécharger pdf

assembly instructions

Family: Stratford Item No. 1351 AU/MB

1. Find a clear area in which you can work.

2. Unpack ﬁxture and glass from carton.

3. Carefully review instructions prior to assembly.

*** The construction of this ﬁxture will be accomplished by ﬁrst making all necessary

electrical connections, mounting the ﬁxture to pre-installed post and then lamping

ﬁxture.

start here

1351

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)

AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING

INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED

ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

Note: Maximum wattage for 1351 ﬁxture is 100 watts per bulb.

Make electrical connections from supply wire to ﬁxture lead wires. Refer to instruction

sheet (I.S. 18) and follow all instructions to make all necessary wiring connections.

Then refer back to this sheet to continue installation of this ﬁxture.

Drawing 1 - Fixture Mounting

Drawing 2 - Glass Replacement

1. Fixture is mounted using 3 - 1/4-20 set screws.

2. Make all necessary electrical connections following wiring instructions below.

Glass Replacement Instructions - see Drawing 2.

1. Remove roof (2) from cage (1) by unscrewing the 2 ball knobs (3) on opposite sides

of the ﬁxture.

2. Remove the 4 glass clips (4) by removing the screws (5) that hold them in place.

3. Pull out glass assembly.

4. To insert replacement glass, follow steps 1-3 in reverse order.

1. After wiring connections are complete, slip post ﬁtter (A) over top of pre-installed

post (B) making sure all wire connections are tucked inside the pole - see Drawing 1.

2. When ﬁxture is slipped over pole make sure no wires are being pinched between the

top edge of the pole and the inside of the post ﬁtter.

3. Thread the 3 set screws (C) into pre-tapped holes in post ﬁtter.

4. Tighten screw (C) to secure ﬁxture to post.

5. To lamp ﬁxture, unscrew ﬁnial (3) from top of roof (2) and remove roof (2) from main

body (1) - see Drawing 2.

6. Fixture can now be lamped accordingly.

7. To reassemble, follow step 5 in reverse order.

3.28.08

H I N K L E Y L I G H T I N G 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com

1 2

Résumé du contenu

Page 1 - Drawing 2 - Glass Replacement

assembly instructionsFamily: Stratford Item No. 1351 AU/MB 1. Find a clear area in which you can work.2. Unpack ﬁxture and glass from carton.3. C

Page 2

I.S. 18 wiring grounding instructionsSAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPL

Commentaires sur ces manuels

Pas de commentaire

Hinkley-lighting STRATFORD 1351 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Hinkley-lighting STRATFORD 1351. Hinkley Lighting STRATFORD 1351 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Hinkley-lighting STRATFORD 1351