Hinkley-lighting BRIGHTON 2298 Manuel d'utilisateur télécharger pdf

assembly instructions

Family: Brighten Item No. 2298

1. Find a clear area in which you can work.

2. Unpack ﬁxture and glass from carton.

3. Carefully review instructions prior to assembly.

*** The construction of this ﬁxture will be accomplished by ﬁrst mounting the

mounting strap to the junction box, making all necessary electrical connections,

mounting the ﬁxture to the wall, lamping the ﬁxture, and then installing the glass .

start here

2298

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)

AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING

INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED

ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

Drawing 2 - Fixture Assembly

Make electrical connections from supply wire to ﬁxture lead wires. Refer to instruction

sheet (I.S. 18) and follow all instructions to make all necessary wiring connections.

Then refer back to this sheet to continue installation of this ﬁxture.

Drawing 1 - Fixture Mounting

1. Prepare mounting strap (A) by threading the two 1 1/4” long mounting screws (B)

into the back of the mounting strap (A) - see Drawing 1 .

• Be sure the holes into which the screws are threaded match the spacing of holes (D)

in the backplate (E) .

2. Attach mounting strap (A) to junction box (J) using two 1” screws (C) .

1. To mount ﬁxture, slip the two mounting screws (B) through the two mounting holes

(D) in the backplate (E) - see Drawing 1 .

2. While holding ﬁxture in place, thread the two ball knobs

(F) on to the end of the

mounting screws (B) , and tighten.

6.01.11

1. To install glass, slip glass panel (1) through bottom of cage assembly (2) - see

Drawing 3 .

2. Slip top of glass panel (1) under top glass clips (3) .

3. Slip bottom of glass panel (1) into the bottom of the cage assembly (2) .

4. Bend lower glass clips (4) up to retain glass panels (1) .

5. Repeat steps 1-4 for remaining panels.

6. Fixture can now be lamped accordingly.

Drawing 2 - Fixture Assembly

1. Prior to installing glass and lamping xture the bottom roof must be removed by

remove bottom knob (4) and then slipping cap (3) and bottom roof (2) of of cage

assembly (1) - See Drawing 3.

7. Replace bottom roor by following Step 3 in reverse.

H I N K L E Y L I G H T I N G 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com

1 2

Résumé du contenu

Page 1 - Drawing 1 - Fixture Mounting

assembly instructionsFamily: Brighten Item No. 22981. Find a clear area in which you can work.2. Unpack ﬁxture and glass from carton.3. Careful

Page 2

I.S. 18 wiring grounding instructionsSAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPL

Commentaires sur ces manuels

Pas de commentaire

Hinkley-lighting BRIGHTON 2298 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Hinkley-lighting BRIGHTON 2298. Hinkley Lighting BRIGHTON 2298 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Hinkley-lighting BRIGHTON 2298