Hinkley-lighting CASCADE 1831 Manuel d'utilisateur télécharger pdf

assembly instructions

Item No. 1831

1. Find a clear area in which you can work.

2. Unpack ﬁxture and glass from carton.

3. Carefully review instructions prior to assembly.

start here

1831

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)

AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING

INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED

ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

Make electrical connections from supply wire to ﬁxture lead wires. Refer to instruction

sheet (I.S. 18) and follow all instructions to make all necessary wiring connections.

Then refer back to this sheet to continue installation of this ﬁxture.

Drawing 1 - Installing lamp

*** The construction of this ﬁxture will be accomplished by ﬁrst lamping the

ﬁxture making all necessary electrical connections, and then mounting the

ﬁxture to pre-installed

post.

01.01.13

Drawing 3 - Fixture installation

1. After wiring connections are complete, slip post ﬁtter (F) over top of pre-installed

post (D) making sure all wire connections are tucked inside the pole - see Drawing 3.

2. When ﬁxture is slipped over pole make sure no wires are being pinched between

the top edge of the pole and the inside of the post ﬁtter.

3. Thread the 3 set screws (E) into pre-tapped holes in post ﬁtter.

4. Tighten set screws (E) with allen wrench provied to secure ﬁxture to post.

ground wires

H I N K L E Y L I G H T I N G 33000 Pin Oak Parkway Avon Lake, OH 44012 8 00 .4 46 .5539 / 440.653 .5 50 0 h in kleylightin g.com

Drawing 2 - Glass Replacement

GLASS INSTALLATION OR REPLACEMENT: please follow the instructions below:

1. Reach up into roof (B) of ﬁxture, and on the side, unthread barrel knob (1) and remove

- see Drawing 2.

2. Lift glass clip (2) upward and remove. Repeat process for other side making sure to

support glass when second clip is removed.

3. Install / remove glass (3) slip glass into ﬁxture or remove broken glass by lifting up.

When installing glass slip bottom of glass into support slot in bottom of ﬁxture.

4. Slip glass clips (2) over top of glass and thread barrel knob (3)

back in place to secrure glass, repeat for other side.

1. To install lamp in ﬁxture slip bulb (A) throught opening in bottom of ﬁxture

roof (B) - see Drawing 1.

2. Thread bulb (A) into socket.

1 2

Item No. 1831 1

Résumé du contenu

Page 1 - Item No. 1831

assembly instructionsItem No. 18311. Find a clear area in which you can work.2. Unpack ﬁxture and glass from carton.3. Carefully review instructions p

Page 2

I.S. 18 wiring grounding instructionsSAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPL

Commentaires sur ces manuels

Pas de commentaire

Hinkley-lighting CASCADE 1831 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Hinkley-lighting CASCADE 1831. Hinkley Lighting CASCADE 1831 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Hinkley-lighting CASCADE 1831