Hinkley-lighting TRUMAN 4021AN Manuel d'utilisateur télécharger pdf



assembly instructions

Family: Truman Item No. 4021

1. Find a clear area in which you can work.

2. Unpack ﬁxture and glass from carton.

3. Carefully review instructions prior to assembly.

*** The construction of this ﬁxture will be accomplished by ﬁrst assembling the

main body of the ﬁxture, making all necessary electrical connections, hanging

the ﬁxture from the ceiling, and then installing the glass.

start here

4021



SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)

AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING

INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED

ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

Drawing 2 - Fixture Assembly

01.01.12

Drawing 1 - Fixture Assembly

1. Rotate arms (1) attached to canopy, until they are equally spaced 120

degrees apart - see Drawing 1.

2. Attach ring (2) by lining up the three holes (B) in the ring with the 3 holes (C) in

the arm (1) and threading in the at head phillips screws (3) to secure ring - see

Drawing 2.

Drawing 5 - Glass installation

NOTE: Fixture can be lamped accordingly prior to glass installation.

1. To install glass, thread tube (4) into coupler (D) approximately 3/8”, making sure

hex nut (5) on the tubing is near coupler - see Drawing 5.

2. Tighten hex nut (5) against coupler (D) to secure tube (4).

3. Slip glass (6) onto xture and up against ring (2) and hole in position.

4. Slip rubber washer (7) followed by steel washer (8) over tube (4), and hold in

position.

5. Thread hex nut (9) onto tube (4) and tighten to secure glass (6).

6. Slip cap (10) onto tube (4), and then thread nial (11) onto end of stem (4) and

hand tighten only, to complete assembly.

Drawing 4 - Fixture Mounting

Drawing 3 - Strap Detail

1. Install screws (A) into mounting plate (B) - see Drawing 3.

• Be sure the holes into which the screws are threaded match the spacing of holes (D)

in the canopy (E) - see Drawings 1 and 2.

2. Attach mounting plate (B) to junction box (J), using screws (G) provided and then slip supply

wires through large center hole.

1. Hang the xture by slipping canopy (D) over screws (B) in the mounting strap - see Drawing 4.

2. Thread on ball knobs (E) onto the end of screws (B) and tighten to secure xture to ceiling.

H I N K L E Y L I G H T I N G 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com

1 2

Résumé du contenu

Page 1 - Drawing 3 - Strap Detail

assembly instructionsFamily: Truman Item No. 40211. Find a clear area in which you can work.2. Unpack ﬁxture and glass from carton.3. Carefully

Page 2

I.S. 18 wiring grounding instructionsSAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPL

Commentaires sur ces manuels

Pas de commentaire

Hinkley-lighting TRUMAN 4021AN Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Hinkley-lighting TRUMAN 4021AN. Hinkley Lighting TRUMAN 4021AN User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Hinkley-lighting TRUMAN 4021AN