Hinkley-lighting BRIGHTON 2297 Manuel d'utilisateur télécharger pdf



assembly instructions

Family: Mission Item No. 2297

1. Find a clear area in which you can work.

2. Unpack ﬁxture and glass from carton.

3. Carefully review instructions prior to assembly.

*** The construction of this ﬁxture will be accomplished by ﬁrst assembling

main body of the ﬁxture, installing the ﬁxture glass, making all necessary

electrical connections and then mounting the ﬁxture to pre-installed post.

start here

2297

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)

AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING

INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED

ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.



Make electrical connections from supply wire to ﬁxture lead wires. Refer to instruction

sheet (I.S. 18) and follow all instructions to make all necessary wiring connections.

Then refer back to this sheet to continue installation of this ﬁxture.

Drawing 2 - Glass Installation

Drawing 3 - Fixture Mounting

Drawing 1 - Fixture Assembly

1. Fixture is mounted using 3 - 1/4-20 set screws.

2. Make all necessary electrical connections following wiring instructions below.

1. After wiring connections are complete, slip post ﬁtter (A) over top of pre-installed

post (B) making sure all wire connections are tucked inside the pole - see Drawing 3 .

2. When ﬁxture is slipped over pole make sure no wires are being pinched between

the top edge of the pole and the inside of the post ﬁtter.

3. Thread the 3 set screws (C) into pre-tapped holes in post ﬁtter.

4. Tighten screws (C) to secure ﬁxture to post.

01.01.12

1. To install glass, unscrew top knob (1) from center stem (4) - see

Drawing 1.

4. Slip glass panel (G) through top of cage assembly (5) - see Drawing 1 and 2.

5. Slip bottom of glass panel (G) into the bottom of the cage assembly (5).

6. Slip top of glass panel (G) up against cage assembly (5) .

7. Bend upper glass clips (6) down to position glass panels (G).

8. Bend lower glass clips (7) up to secure glass panels (G).

9. Repeat steps 2-6 for remaining panels.

10. Fixture can now be lamped accordingly.

11.

2. Remove cap (2).

3. Slip roof (3) o of center stem (4), glass can now be installed.

Replace roof by following steps 1-3 in section 2 in reverse order.

H I N K L E Y L I G H T I N G 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com

1 2

Résumé du contenu

Page 1 - Drawing 1 - Fixture Assembly

assembly instructionsFamily: Mission Item No. 2297 1. Find a clear area in which you can work.2. Unpack ﬁxture and glass from carton.3. Carefull

Page 2

I.S. 18 wiring grounding instructionsSAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPL

Commentaires sur ces manuels

Pas de commentaire

Hinkley-lighting BRIGHTON 2297 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Hinkley-lighting BRIGHTON 2297. Hinkley Lighting BRIGHTON 2297 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Hinkley-lighting BRIGHTON 2297